We plan to stick as closely to these posted turnaround times as possible but due to staff de-densification and the need to maintain social distancing we may not be able to offer some services as quickly as in the past. *NOTE* During COVID-times please plan for an additional day or two for completing your projects. Make an appointment with us to discuss your project! In many cases we will be able to finish your project in less time, but use these times for planning purposes. Please keep in mind the following minimum turnaround times when planning your projects. These instructions are applicable to the following pho.
#MICCA PHOTO BATCH REPROCESSING TUTORIAL SERIES#
I have changed the mechanism a now, at all crossing point, we should have the 1min rolling avg target nits instead (if reachable) as I wanted initially.Ĭombination of a) and b) solved issues and the one I have looked at.Īnd as I said before, the "Chapter FALL merge" of 500% could be lowered and could be the value of the "Smart max Speed" of 5 (0,5%) if any other brightness change would be visible.īut let's wait for feedback before changing those.Our goal in the Service Bureau is to complete your orders properly in as timely a manner as possible. This video demonstrates the steps in updating the firmware for a Micca NEO series digital photo frame. This meant that the crossing point value was not representative of the LOCAL situation.
#MICCA PHOTO BATCH REPROCESSING TUTORIAL FULL#
The new FALL algo helps a lot in that matter.ī) the crossing point of the "rolling average" within each chapter was NOT using (in most cases) a 1min rolling average value but the FULL chapter average instead (but it should have.) I looked at the issue with visible brightness change reported by but also at some other movies where I had spotted such behaviour myself.Ī) in all case, it was for low target nits changing between 50nits and 150+nits. All you and your loved ones have to do is sit back and relive those treasured memories. No complicated setup, simply insert a SD card or USB drive with photos, turn it on, and it does the rest. What it does it set the target nits in such a way that the BT2390 Knee is equal to the current frame FALL (at least with 100% dynamic tuning).ģ) Improvement of the "Smart Max Speed" algo. Easy to use by design, Micca NEO photo frames are ready to go right out of the box. (Graphic by Matt Poor/Image Courtesy of Elevance Health). It's a hidden algo hidden in the FALL algo if you select a "No compression limit" value of 1. The common denominator in the healthcare SPAC craze is technology, Micca said, accelerated by. If anybody prefer to use the good old FALL algo, then he can choose 150nits instead of the 0 for the no compression limit.īut I like the new FALL algo with BT2390 100nits Knee calculation better (and this also helps test scene)Ģ) A new Target nits experimental algo just for fun that we could call BT2390Knee Algo: In between the additionnal FALL part is scaled. If the FALL was high, then it would add up to those 150, and you would end up most of the time with a pretty higher target nits like ~200nits even if the peak itself was also only 200nits.Īnyway, now we only have Target= Peak Nits for any frames with a peak lower than 100nits.įor frames with a peak higher than 100nit, we calculate what the Bt2390 target nits needs to be to protect the 0-100nits from compression.Īnd we use the Min between 150 and the calculated BT2390TargetMin (target to protected 0-100nits) instead.Īlso the FALL is not added if BT2390TargetMin=100nits but is fully added by the time BT2390TargetMin reaches 150 nits (which is for about 250 peak nits as can be seen in the table below). Target Nits(i)= Math.Min(2 * arrHL(i), dblMinTarget + Math.Max(1, 2 * dblTuning / 50) * arrSKYFALL(i))which meant that any frame with a peak higher than 150 nits, had a target nits higher than 150 as well.
0 kommentar(er)
